The adapter plate is attached between the rocker and the sensor. It relocates the sensor outwards by 10 mm. We recommend mounting the adapter plate when the badassBox rubs against the spokes. This ensures that the badassBox maintains its full functionality. The adapter has absolutely no effect on the dismounting or mounting of the badassBox. Extra wide offset. Only needed for special purposes. Usually the 5 mm adapter is sufficient.

This adapter plate is installed between the swing arm and the sensor. It offsets the sensor by 5 mm to the outside. We recommend to mount the adapter plate when the badassBox grinds on the spokes. Thus, the full function of the badassBox is preserved. The adapter has absolutely no effect on the removal and installation of the badassBox.

The Adapthor is an adapter with which you can mount your badass box with cable ties at any position on the chain stay. Especially suitable is the Adapthor for tight mounting situations, such as on road bikes and gravel bikes. A suitably trimmed pad from self-adhesive elastic foam is optional. This pad can be glued to the Adapthor to attach this to the chain stay without the risk of scratches.

The Badass bottle holder is made of carbon, so it has not only a nice design but also a low weight. Due to the special shape of the bottle holder, your bottle will fit ideally and will hold even under difficult conditions.

Spare part for badassBox 4The cover fits on all version 4 badassBoxes. The snap locks provide a secure hold.

The Slim Speed Sensor is found on bikes with Bosch motors, especially on the so-called Smart System. The speed sensor is either integrated in the rear axle area or - classically - mounted on the chain stay by means of a Bosch adapter. The presence of a spoke magnet indicates that it is mounted on the chain stay, whereas a magnet on the brake disc indicates that it is integrated. With the Slim Adapter you can place the Slim Speed Sensor (in case of integrated mounting) to a suitable place on the swingarm and fix it with cable ties or - in case of chainstay mounting - screw it to the chainstay instead of the original Bosch adapter. In both cases, our Slim Adapter ensures the use of the badassBox 4 Bosch. Installation The Bosch Slim Sensor is either mounted on the chain stay or integrated into the dropout. Here the slim speed sensor is classically mounted on the chain stay with an adapter. There, the sensor must be freed from the adapter, the original adapter is unscrewed and replaced by our adapter. Here the slim speed sensor is integrated near the rear axle. First, the rear wheel must be removed. Then the sensor is removed from the bracket and mounted with our adapter at a suitable place on the chain stay using cable ties.

Description Double-walled construction - keeps liquids cool twice as long as conventional bottles Optimized cage fit - Fits almost all standard bottle cages Easy to clean - all parts can be separated for thorough cleaning Easy squeeze - get more fluid with less effort Protective cap over mouthpiece - drink water, not dirt High flow self-sealing cap - maximizes flow rate while preventing splashes and spills Featuring Trutaste™ polypropylene with Hydroguard™ - taste your water and nothing else (tasteless) Positive barrier - for leak-proof transport Guaranteed to be free of harmful BPA, BPS, BPF Technical data MaterialBPA-free Trutaste™ polypropylene Featuresspill-proof valve Dimensions 7.3 x 7.3 x 23.8 cm Weight130 g Volume710 ml Colornavy perforated

Description Double-walled construction - keeps liquids cool twice as long as conventional bottles Optimized cage fit - Fits almost all standard bottle cages Easy to clean - all parts can be separated for thorough cleaning Easy squeeze - get more fluid with less effort Protective cap over mouthpiece - drink water, not dirt High flow self-sealing cap - maximizes flow rate while preventing splashes and spills Featuring Trutaste™ polypropylene with Hydroguard™ - taste your water and nothing else (tasteless) Positive barrier - for leak-proof transport Guaranteed to be free of harmful BPA, BPS, BPF Technical data MaterialBPA-free Trutaste™ polypropylene Featuresspill-proof valve Dimensions 7.3 x 7.3 x 23.8 cm Weight111 g Volume620 ml Colorsage perforated

Description Double-walled construction - keeps liquids cool twice as long as conventional bottles Optimized cage fit - Fits almost all standard bottle cages Easy to clean - all parts can be separated for thorough cleaning Easy squeeze - get more fluid with less effort Protective cap over mouthpiece - drink water, not dirt High flow self-sealing cap - maximizes flow rate while preventing splashes and spills Featuring Trutaste™ polypropylene with Hydroguard™ - taste your water and nothing else (tasteless) Positive barrier - for leak-proof transport Guaranteed to be free of harmful BPA, BPS, BPF Technical data MaterialBPA-free Trutaste™ polypropylene Featuresspill-proof valve Dimensions 7.3 x 7.3 x 23.8 cm Weight111 g Volume620 ml Colorwhite/black

Description Double-walled construction - keeps liquids cool twice as long as conventional bottles Optimized cage fit - Fits almost all standard bottle cages Easy to clean - all parts can be separated for thorough cleaning Easy squeeze - get more fluid with less effort Protective cap over mouthpiece - drink water, not dirt High flow self-sealing cap - maximizes flow rate while preventing splashes and spills Featuring Trutaste™ polypropylene with Hydroguard™ - taste your water and nothing else (tasteless) Positive barrier - for leak-proof transport Guaranteed to be free of harmful BPA, BPS, BPF Technical Specifications MaterialBPA-free Trutaste™ polypropylene Featuresspill-proof valve Dimensions 7.3 x 7.3 x 24 cm Weight136 g Volume620 ml Colorblack

The Mud Cap is compatible with all new Podium® bottles launched since 2019, including Podium® Chill, Podium® Big Chill and Podium® Ice, and can also be ordered as spare part for Podium® Chill Dirt can be ordered. No matter which bottle you prefer, you can now drink clean. Features Easy installation - attaches to existing nozzle Made of one piece silicone BPA, BPS and BPF free Technical data Material  Silicone Weight6 g Colorblack

The Badass CS adapter allows the mounting of the pin-shaped sensors, which are used e.g. for Flyer with Panasonic motors or Bulls with Brose motors, so that the badassBox can be used. Installation The pin-shaped CS sensor is located in the area of the dropout. To get to the sensor you have to remove the rear wheel. Unscrew the screws of the bracket that secures the sensor to the dropout. Separate the sensor from the bracket. Insert the pin-shaped sensor into the adapter so that the flat side of the sensor is aligned with the corresponding recess in the adapter. The sensor must be inserted completely into the adapter, so that only the cable protrudes and the snap closes flush with the surface of the adapter. (In the photo, the sensor is not yet completely inserted). Attach the adapter to the frame of your bike with the supplied cable ties. Reinstall the rear wheel. Slide the badassBox onto the adapter until it clicks into place. Mount the spoke magnet and align it with the edge of the badassBox housing. That's it. Have fun with your faster e-bike!

A distance bush is a spacer that is used whenever either a distance needs to be created between two components or when it is necessary to bridge a distance. If you need a little more distance, we also have a 5 mm Distance bush on offer. Technical data Material Polyrthylene PE Dimensions  5.3 x 15 x 2.5 mm Colorblack

A distance bush is a spacer that is used whenever either a distance needs to be created between two components or when it is necessary to bridge a distance. If you need a little less distance, we also have a 2.5 mm Distance bush on offer. Technical data Material Polyrthylene PE Dimensions  5.3 x 15 x 5 mm Colorblack

The badass G4 adapter allows the attachment of the G4 speed sensor from Bosch, which are used for example on Trek with Bosch motors, at a suitable location on the chain stay so that thereby the badassBox 4 Bosch can be used. A suitably trimmed pad from self-adhesive elastic foam is optional. This pad can be glued to the G4 adapter to attach this to the chain stay without the risk of scratches. Installation The integrated G4 Speed Sensor is located in the area of the dropout. To get to the sensor you have to remove the rear wheel. With the included button head screw you can screw the G4 speed sensor to the G4 adapter (1). (2) A suitably cut pad made of self-adhesive elastic foam is included as an option. This pad can be glued to the G4 adapter to attach it to the chain stay without the risk of scratches. With the enclosed cable ties (3), you can mount the G4 adapter including screwed G4 speed sensor at a suitable location on the chain stay (4), where it is possible to slide the badassBox over the adapter.

Original housing cover with the badass eBikes logo and click closure. Suitable for all badassBoxes Type3.3 with 43mm.

Original housing cover with the badass eBikes logo and click closure. Suitable for all badassBoxes Type3.3 with 46mm.

Original housing cover with the badass eBikes logo and click closure. Suitable for all badassBoxes Type3.4.

CNC milled aluminum dispenser with brass components. CNC knob for easy and controlled inflation. The double valve head fits Presta and Schrader valves. The neoprene cover protects the hand during the discharge from the cold. Only compatible with threaded CO2 cartridges. Description with hardened stainless steel pin for piercing the cartridge Slip fit valve for Presta and Schrader valves compatible with all cartridges with thread with turret valve for precise inflation .responsive-video { position: relative; padding-bottom: 56.25%; padding-top: 30px; height: 0; overflow: hidden; } .responsive-video iframe { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Pump up the volume Compact, lightweight hand pump with efficient, overlapping composite matrix handle. Cylinder and piston made of CNC machined aluminium, optimised for high pressure applications. Equipped with ABS flex hose; Presta and Shrader valve compatible. Includes lightweight composite matrix frame holder.

Versatile design combines the efficiency of a hand pump with the convenience of CO2. Innovative 2-in-1 inflation system works as a high pressure hand pump or CO2 inflator. Integrated steel-braided CO2 Flex Hose (CFH) doubles as a CO2 dispenser. Pump features a CNC machined aluminum body, piston and handle. Flip-Thread Chuck works on both Presta and Schrader valves. Kit includes: Pump with integrated CFH hose, one 16 g cartridge and CFH mounting hardware. Adaptable configuration conveniently mounts to frame or slides into jersey pocket. Compatible with threaded CO2 only.

The size of Trump's brain Small tool for great deeds. The RAP6 is extremely robust and super lightweight. Ergonomic forged aluminum side plates. Forged, wrapped Center-Pivot CrV+ anti-corrosion bits. Chrome Vanadium steel fastening hardware.

Low profile multi-tools optimized for modern component groups. CNC machined aluminum side plates. Chrome Vanadium steel fastening hardware.

Low profile multi-tools optimized for modern component groups. CNC machined aluminum side plates. Forged, Center-Pivot CrV+ anti-corrosion bits. Chrome Vanadium steel fastening hardware.